Maxtor 4Channel Stand-alone DVMR Spécifications

4 Channel Standalone DVRUSERS MANUAL

is:"1" is:"2" is:"3" is:"4" is:"5"Select this item to set up current time

(1)Range: 0-24 hrs.(2)Set “T” for continuous recording.(3)Set “M” for motion recording.(4)Set up “ - ” to disable the recording.RECORD SCHEDULE

1. Setup the First Detective Area First, Press (UP, DOWN, FF, REW ) to Set the UPPER-LEFT Point of the First Detective Area. Then, Press (UP,

NETWORK SETUP NETWORK MENUACCEPT CLIENTMAC ADDRESSIP ADDRESSSUBNET MASKGATEWAYPORT NUMBER(YES)00:00:00:73:37:31192.168.001.090255.255.255

(1)Press to start recording.(2) During recording, the mark ” * ” appears in status of overwriting RECORD CONTROL(3)PLAYBACK : *Press to s

．12．IntroductionThis document is the Operation Manual for the 4 CH Stand Alone DVR PC Viewer. The application will show you stream image stored in the

．13．Fig.1. No DVR Storage Device Message DVR PC ViewerA. User InterfaceThe default page of the application is DVR Storage Device PC Viewer. The user

．14．B. Functionsi. MYS Player ButtonIf you want to see MYS file which was stored in your PC, press this button or press [F2] key.ii. DVR Storage Devic

．15．Press button (or [ 5 or Numpad 5 ] Key) to see all 4 channels at the same time.Press button (or [ 1 or Numpad 1 ] Key) to see channel 1 enlarged

．16．vii. Screen Capture ButtonIf you wan to capture the screen, follow the screen capture procedure listed below:* Using “Positioning Slider Bar” find

．17．(1)(2)(3)(4)(5)(6)(7)(8)(9)(10)ScreenMYS File Select DialogPositioning Slider BarPC Viewer ButtonFile Open ButtonMYS file informationMYS File Play

．18．vi. Audio ControlFig.11. Audio Control ButtonsPress button to enable sound. Once sound is enabled, the button icon will be changed to

．19．Remote DVR ClientIntroductionTerms in This DocumentRequirementOSDirectXOS of your PC should be Windows 2000/XP or later.Your PC should be equipped

．20．Fig.1. Remote DVR ClientBefore you connect to your DVR, make sure that your DVR is correctly configured for thenetwork connection. If your DVR is

．21．Type the IP address and Password and press Connect button. You can save the IP address forfuture use by checking “Save IP.” Once an IP address sav

．22． Audio ControlA.Audio Sounding/MutePress button, or press [Ctrl+M] Key, to activate audio when the client is connected to theDVR or the c

．23．There are two options for starting DVR playback.i. Timed Play The upper part of the window shows the time range of the stream stored in the DVR

．24．Fig.11. PC Capturing ButtonsA. CapturingPress button (or press [Ctrl+R]) to start capturing. When it is capturing, the StatusWindow will s

．25．i. PC Playback StatusWhen the application is in PC Playback mode, you will see playback state indication at thebottom, left. It shows the current

．26．A. Change Client SettingTo change the configuration of the client application, select[main menu -> Configuration ->Configure Client] or pres

CONTENT FEATUREFRONT PANELREAR PANELCONTROL PANEL BUTTONSPECIFICATIONSOPERATING MANUALVIEW CONTROLPLAYBACK CONTROLRECORD CONTROL4 CHANNE

．27．Fig.19. Stream Capturing DirectorySelect folder and press OK to change directory.iv.Message BoxesFig.20. On/Off the confirm message boxes.B. Chang

．28．i. Record Mode You can change DVR recording mode. [EACH or QUAD]ii. Record Quality You can adjust stream picture quality. [HIGH NORMAL LOW]i

．29．If you want to format the HDD, press “Format Master (or Slave) HDD” button. You should knowthe DVR management password to format the HDD.D.Change

．30．If any change is made, the “OK” button will be activated. Press “OK” to change the time.Press “Cancel” to close the window without changing the DV

CH1CH2CH3CH4．31．18ALM-CH1ALM-CH2ALM-CH3ALM-CH4ALM-GNDRLY-COMRLY-NCRLY-NOBROWNREDORANGEYELLOWGREENBLUEBLACKWHITE12345678 ALARM & LOOPING CABLE

R12C403001

Removable HDD RACK．1．1、Definitely Standalone.2、Real Time Refresh Rate.3、Display While Recording.4、Frame Recording & Quad Recording.5、Support Audio

．2． REAR PANEL★◆●The standard for car usageThe standard for home usageThe advanced for home usageDC12~24VVCRMONITORINOUTVIDEO INCH1CH3CH2CH4VIDEO OU

CONTROL PANEL BUTTON．3．CONTROL BUTTONS in the VIEW MODEMenu: Enter the MENU MODE for the system setup.(Recording and Playback needs to be stopped be

．4．CONTROL BUTTONS in the PLAY MODECONTROL BUTTONS in the PLAYBACK EVENTS SEARCH MODEExit: Go back to the VIEW MODE.Play: Playback the selected stream

SPECIFICATIONSVideo InputVideo Input ChannelVideo Output ChannelDisplay FrameNTSC PAL4CH Composite2CH Composite (VCR OUT / MONITOR OUT)100 fps (

OPERATING MANUAL (MAIN MENU)SYSTEM SETUP SYSTEM SETUPSYS EM STANDARD PALAUDIO RECORD : OFFAUDIO MUTE : O